Modeling intensity field from high-intensity ultrasound source WITHOUT...
Hi, I cannot afford to buy the Acoustics module, so I'm wondering if it's possible to model the energy being deposited into a material due to multiple ultrasound sources. The KZK equation can be used...
View Articlehow to get the average values on parallel channels
Hello everybody. Now I simulate the hydynamics of the distributor with parrallel channels. I want to get the mean velocity values in the middle of each channels. I try to use the 'cut plane' on the...
View ArticleSave data to a text file using MATLAB LIVELINK with COMSOL
Hi All, I have one COMSOL GUI model which runs perfectly. I save the model as .m file and run in MATLAB. In the COMSOL desktop, I use the export command to extract data. Therefore, I am expecting when...
View ArticlePCF, PML
Hi, I am designing a PCF with hexagonal pattern having five air hole rings. pitch = 1 um. air filling fraction = 0.90 i have used circular PML to get the imaginary part of refractive index. what should...
View ArticleHC-PCF
Hi , I would like to calculate the hollow PCF, as I know, normally we should know the bandgap of the fiber, then calculate the fundamental mode. is it feasible to calculate the bandgap by using Comsol...
View ArticlePreview of open model
When opening model files, there is possibility to show the preview of model. But all models result in the message "No preview available". How may I switch this possibility on?
View ArticleQuestions for electric fields in 2D vs. 3D model of capacitor.
Hi guys. I am trying to model a structure, which has a capacitor build into it with SiO2 and air as dielectric. For this I started to model a 2D structure and plotted the electric field as "electric...
View ArticleHow to simulate the water boiling by Level-Set method
There is a good example simulating water boiling by phase field. I am trying to use the Level-Set method. However, I was frustrated by many times of failure. My problem is how to deal with the...
View ArticleDealing with Periodic Boundary Conditions, PMLs and interfaces.
Hello, I'm trying to simulate a nanoparticle array over a substrate in order to study its extinction cross-section. To do so I've made a cell with periodic boundary conditions on the sides and two PMLs...
View ArticlePrincipal stress 2d vs 3d
Hi everyone, I have the same model made in 2d and 3d. First and second pricipal stresses are similiar in both models. But third principal stress in 2d are unrealistically high, however in 3d have value...
View ArticleExtracting absorbed power
Hi all! I am currently doing a 2D model where I have an incoming power, and then I have absorption within the material. As a result, I have the value of the intensity everywhere, but I don't know how...
View Articlehi
can anyone explain to me what is geometry linearity and non linearity? what is the different between them? i'm not clear about that... thank you for advanced... :)
View Articlesolving helmholtz equation
I wish to solve Helmholtz equation for an Axi-symmetric geometry. The problem geometry consists of a excitation source a tube and air box (all rectangles). Is it possible in equation based modeling?....
View ArticleTransient Hot Wire Method
Hi Everyone! I'm new on COMSOL so I don't know too much yet. I need to simulate the transient hot wire method, I don't know how to start with, and I cannot find any example. Could somebody help me with...
View ArticleRegular Meshing
Hi all, I've been asked to create a regular mapped mesh for a cube which has faces of 10 by 10 square areas throughout the whole of the cube. I'm applying a magnetic field to the cube and I wanted to...
View ArticleMagnetic field
Does anybody know how to write this expression on comsol ( ∇/B/^2 )? I meant expression that replace "the gradient of the magnetic field norm square". Thank you
View ArticleHow can I set input source for example port 1and port 2 when we want to the...
I want to see the interference between two waveguides. It is simple. There are two waveguides. And laser inputs are on the end of the waveguides. So I need two inputs. By using a boundary mode analysis...
View ArticleFailed to evaluate variable jacobian - using a step function
Hi every one, Im trying to put a BC (volumetric flow rate) in my model as a step function. But the following error occur: Failed to evaluate variable Jacobian. - Variable: step1 - Geometry: 1 - Point:...
View ArticleMax value of a field and its coordinates
Hello, I know that there have been a lot of posts about this topic and I have read many of them but I am still as dumb as before. I need to find the value of the maximum value of the field in a domain...
View ArticleUse contour plots as geometric entities
I saw in the release highlight video that in v4.3a that you can use contour plots as geometric entities. How do you do this?
View Article